Electronic Modules

Bluetooth master and slave moduleThrough the AT command, you can set this bluetooth module to the master mode can also be set to slave mode, even in iBeacon way work .it also Supports Apple Notification Center Service (ANCS)
base Board 4 PIN, leads to VCC, GND, TX, RX. You can be very convenient to connect to your arduino project or other DIY project
Working voltage 3.6 V to 6V,Default rate of 9600.There are 4PIN dupont cable in the package

Micro SD TF card reader module SPI interface with chip level conversion
Support Micro SD card, Micro SDHC card (high speed card)
board level conversion circuit, namely the interface level for 5V or 3.3V
power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
The communication interface is a standard SPI interface
M2 screw positioning holes for easy installation

Infrared IR Wireless Remote Control Sensor Module Kits for Arduino
For Arduino suite by ultrathin Mini infrared wireless remote control infrared remote control and 38 KHZ infrared receiving module,
the Mini ultra-thin has 20 function keys, the infrared emission furthest distance up to 8 meters,
very suitable for indoor control devices of all kinds.
Infrared remote control receiving module can receive standard 38 KHZ modulation signals, by means of programming the Arduino,

CH340 Serial Port Debugger USB to TTL Converter CH340G module STC Download Cable Adapter Module

5V 2 Channel SSR Solid State Relay Board Power Switch High Level Trigger
Working Voltage: DC 5V
Working Current: 160mA
Input Control Voltage: 0-2.5V(low level,OFF), 3.3-5V(high level, ON)
Compatible Load: AC 100-240V 2A
Module Size: 55 X 33 X 25mm/2.17 X 1.30 X 0.98inch(L*W*H)

5V Relay 1 Channel SSR Low Level Solid State Relay Module 250V 2A

Arduino Sensor Shield V5.0 Sensor Expansion Board for Arduino UNO R3
Upgraded V5 Arduino Sensor Shield
Buckled brick cables
Size: 57 x 57 x 19mm
Buckled port with VCC, GND and Output

4 Channel 5v Relay Shield Module for Arduino UNO R3

Standard for Shield interfaces and shape
Can continue to stack other for expansion boards
3 M3 screw positioning holes for easy installation
High Drive (5V or 3.3V) normally open contact closure
Onboard relay indicator (red)

1 Channel 5V Relay Module Low level Trigger    1-Channel relay module, with photoelectric isolation    dc or ac signal control, can control 220 v ac load    5v relay, low level trigger

L293D WiFi Motor Drive Expansion Board Shield Module for NodeMCU CP2102
Motor power, control power separation; In the experiment, by short-circuiting block the merger, the VIN and VM short, while power to the motor and the control board
Module provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) while completing motor drive and control

Screw Terminal Expansion Adapter Board for the Arduino Nano V3.0 AVR
Use this dock to add extra connections to your Nano! It uses screw terminals so that you can be sure the connection is strong, and also use thicker/stranded wires.
This dock must be soldered together and a Nano is NOT sold with this item and is only pictured for illustrative purposes.
Package Contents:1 Nano Dock.

L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper fit Arduino Electric Projects, Smart Car Robot
Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.